濟南富強門業有限公司
聯系人:林經理
電話:151 6888 2846
郵箱:527800164@qq.com
地址:濟南市歷下區化纖廠路8號3號樓101號
濟南卷簾門維修攻略:電機控箱更換+故障排查,實用到爆!
濟南卷簾門維修攻略:電機控箱更換+故障排查,實用到爆!
Jinan rolling shutter door maintenance guide: motor control box replacement+troubleshooting, practical to the point of explosion!

濟南廠房、車間的老板們注意了!工業卷簾門突然“罷工”沒反應,耽誤生產不說,找維修師傅又怕被坑?其實很多時候不用急著花錢,先做好基礎故障排查,就算是電機控箱壞了,跟著步驟也能更換。今天這份維修干貨趕緊收藏,不管是自己動手還是監督師傅,都能少走彎路、避開隱患!
Attention, bosses of factories and workshops in Jinan! Industrial rolling shutter doors suddenly go on strike without any response, delaying production and causing fear of being tricked by maintenance technicians? In fact, many times there is no need to rush to spend money. First, do a good job of basic troubleshooting. Even if the motor control box is broken, follow the steps to safely replace it. Today's repair tips should be collected quickly. Whether you do it yourself or supervise the master, you can avoid detours and hidden dangers!
得明確,卷簾門沒反應,先排查簡單問題,再處理復雜故障,別上來就拆修。這3步基礎排查一定要先做,很多時候都是小問題導致的“假故障”:
First of all, it needs to be clarified that the rolling shutter door is not responding. First, investigate simple problems, and then deal with complex faults. Don't just come up and dismantle it for repair. These 3 basic troubleshooting steps must be done first, as many times they are "false faults" caused by minor issues:
步查電源,這是常見的誘因。先看電機控箱的電源有沒有接通,墻上的插座是不是松動,控制箱對應的空氣開關有沒有跳閘。如果是三相電的卷簾門,還要檢查是不是缺相;再順帶著看看電源線有沒有破損、老化,接頭處有沒有松動。很多時候只是插座接觸不良或開關跳閘,重新插緊、合上開關就能恢復正常,省了不少麻煩。
The first step is to check the power supply, which is the most common cause. First, check if the power supply of the motor control box is connected, if the wall socket is loose, and if the corresponding air switch of the control box has tripped. If it is a three-phase electric rolling shutter door, it is also necessary to check if there is a phase loss; Also, check if the power cord is damaged or aged, and if the connectors are loose. Many times, it's just poor socket contact or switch tripping that can be restored to normal by re plugging and closing the switch, saving a lot of trouble.
第二步查遙控器。排除電源問題后,就看遙控器是不是“掉鏈子”了。先檢查電池有沒有沒電,換一組新電池試試;再按遙控器按鍵,看看有沒有指示燈亮,要是沒反應,可能是按鍵失靈或遙控器損壞。這時候可以用控制箱上的手動按鈕操作,要是手動能正常用,就確定是遙控器的問題,不用再折騰電機和控箱了。
The second step is to check the remote control. After ruling out the power issue, check if the remote control is "disconnected". First, check if the battery is running low and try replacing it with a new set of batteries; Press the remote control button again and check if the indicator light is on. If there is no response, it may be due to button failure or damage to the remote control. At this point, you can use the manual button on the control box to operate it. If the manual function is working properly, it is definitely a problem with the remote control, and there is no need to tinker with the motor and control box anymore.
第三步查機械部分。如果電源和遙控器都沒問題,門還是沒反應,就觀察門體本身:軌道里有沒有異物卡住,比如貨物、碎石、油污結塊;門體的連接部位,比如鏈條、卷軸有沒有松動、變形,門體有沒有傾斜卡頓。這些機械卡滯會讓電機負載過大,觸發保護機制導致停機,先清理軌道異物、校正門體位置,再測試是否能正常運行。
The third step is to check the mechanical part. If there are no issues with the power supply and remote control, but the door still does not respond, observe the door itself: whether there are any foreign objects stuck in the track, such as goods, gravel, oil stains, or clumps; Are the connecting parts of the door body, such as the chain and scroll, loose or deformed, and is the door body tilted or stuck. These mechanical blockages can cause excessive motor load and trigger protection mechanisms, resulting in shutdown. First, clean up foreign objects on the track, correct the position of the door body, and then test whether it can operate normally.
要是排查后確定是電機控箱損壞,就按這幾步更換,核心原則是“、接線無誤”:
If it is determined after investigation that the motor control box is damaged, it should be replaced safely according to these steps. The core principle is "safety first, correct wiring":
步必須斷電操作!更換前一定要關閉總電源,拔掉控箱的電源插頭,再用驗電筆確認一下沒有電,避免帶電操作觸電。工業卷簾門的控箱電壓多為380V或220V,觸電風險極高,這一步不能省。
The first step is to shut down the power operation! Before replacement, be sure to turn off the main power supply, unplug the power plug of the control box, and it is best to use a voltage tester to confirm that there is no electricity to avoid electric shock during live operation. The control box voltage of industrial rolling shutter doors is mostly 380V or 220V, and the risk of electric shock is extremely high. This step must not be omitted.
第二步拆卸舊控箱。先拿出手機,把舊控箱上的接線位置拍下來,清晰記錄每根線對應的接口,防止后續接錯。然后用螺絲刀拆下固定控箱的螺絲,輕輕斷開所有接線,注意別扯斷線路,再把舊控箱取下來。
Step 2: Disassemble the old control box. First, take out your phone and take a picture of the wiring positions on the old control box, clearly recording the corresponding interfaces for each wire to prevent future misconnections. Then use a screwdriver to remove the screws that fix the control box, gently disconnect all wiring, be careful not to pull off the lines, and then remove the old control box.
第三步安裝新控箱。把新控箱對準原來的安裝位置,用螺絲固定牢固,確保控箱平整、不晃動。然后對照之前拍的照片,把每根線對應接到新控箱的接口上,注意正負極和相線順序,千萬別接反,不然電機可能反轉甚燒毀。
The third step is to install a new control box. Align the new control box with the original installation position, fix it firmly with screws, and ensure that the control box is flat and does not shake. Then compare with the previous photos and connect each wire to the interface of the new control box. Pay attention to the order of the positive and negative poles and phase wires, and do not connect them in reverse, otherwise the motor may reverse or even burn out.
第四步調試測試。接好線后再次檢查一遍接線是否正確,確認無誤后通電。先用控制箱上的手動按鈕測試門體升降,再用遙控器操作,觀察門體運行是否順暢、停止是否精準,有沒有異響或卡頓。如果一切正常,就說明更換成功;要是有問題,先斷電再檢查接線,避免二次損壞。
The fourth step is debugging and testing. After connecting the wires, double check if the wiring is correct. After confirming that there are no errors, turn on the power. First, use the manual button on the control box to test the lifting and lowering of the door, and then operate it with the remote control to observe whether the door runs smoothly, stops accurately, and whether there are any abnormal noises or jamming. If everything is normal, it means the replacement was successful; If there is a problem, cut off the power first and then check the wiring to avoid secondary damage.
給濟南本地的老板們提個醒:工業卷簾門的電機控箱更換涉及電路和機械,要是自己沒有電工基礎和維修經驗,別硬撐著動手,建議找濟南本地的門業維修團隊上門服務,避免操作不當導致電機燒毀、門體損壞,反而花更多維修費。平時也要注意給控箱做些基礎保養,比如定期清理灰塵、檢查接線松動,能減少故障發生,讓卷簾門用得更久。
Finally, a reminder to local bosses in Jinan: the replacement of the motor control box for industrial rolling shutter doors involves circuits and machinery. If you do not have a foundation in electrical engineering and maintenance experience, do not force yourself to do it. It is recommended to seek on-site service from a professional door repair team in Jinan to avoid improper operation leading to motor burnout, door damage, and even more repair costs. It is also important to pay attention to basic maintenance of the control box, such as regularly cleaning dust and checking for loose wiring, which can reduce the occurrence of faults and prolong the use of the rolling shutter door.
本文由 濟南卷簾門 友情奉獻.更多有關的知識請點擊 http://www.santoncc.cn/ 真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is a friendly contribution from Jinan Rolling Shutter Doors For more related knowledge, please click http://www.santoncc.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
閱讀/ Recommended reading
- 濟南卷簾門維修攻略:電機控箱更換+故障排查,實用到爆! 2025-12-22
- 濟南卷簾門選購指南!7大種類+選型技巧,廠家直訂不踩坑 2025-12-22
- 冬季洗車店濟南卷簾門降不下來?這樣解決又省心 2025-12-20
- 濟南洗車店冬季保溫神器!PVC快卷卷簾門為何成為剛需? 2025-12-19
- 濟南卷簾門快速破拆開鎖的6種方法 2025-12-18
- 濟南防火卷簾門的7種控制方式和常見故障及解決辦法 2025-12-17
- 地下車庫卷簾門壞了,誰負責維修 2025-12-16
- 濟南卷簾門外掛電機安裝調試及故障分析排除 2025-12-15
濟南卷簾門選購指南:種類全解析+選型技巧,選對不踩坑! Jinan Roller Shutter Door Selection Guide: Comprehensive An...


