卷簾門通常適用于門面、、醫院、工廠、車庫等門洞較大的場所，那么你了解卷簾門安裝要求及安裝步驟內容嗎？下面濟南卷簾門廠家為您講解。

Rolling shutter doors are usually applicable to places with large door openings such as doors, shopping malls, hospitals, factories and garages. Do you know the installation requirements and steps of rolling shutter doors? Next, Jinan roller shutter door manufacturer will explain it to you.

１、先復核門洞的尺寸是否與制作尺寸規格相符。

1. First, check whether the size of the door opening is consistent with the manufacturing size.

２．將端蓋板用膨脹螺絲或其它方式與墻體固穩，端蓋板外邊距洞口邊不能小導軌寬度，應比導軌寬Ｓｍｍ左右，保證與墻體垂直，兩端蓋板平行寬度與高度應與制作尺寸一致，允許誤差。

2. Fix the end cover plate with the wall by expansion screws or other methods. The distance from the outer edge of the end cover plate to the hole edge shall not be smaller than the width of the guide rail, which shall be about Smm wider than the guide rail to ensure that it is perpendicular to the wall. The parallel width and height of the cover plates at both ends shall be consistent with the manufacturing size, with allowable errors.

３、用水平管測兩端蓋板對是否平行，誤差＃２毫米。

3. Use a horizontal pipe to measure whether the center of the cover plates at both ends is parallel to the center, with an error of # 2mm.

４、將導軌用螺絲與墻體固定，保證與端蓋板邊、洞口邊平齊，用鉛錘吊線檢測垂直度，誤差＃２毫米。導軌之間的距離應平行相等，誤差＃３毫米。將門軸或門體裝在兩端蓋板上固定。再用水平尺和水平管檢測是否水平，誤差＃２毫米。

4. Fix the guide rail with the wall with screws to ensure that it is flush with the edge of the end cover plate and the edge of the hole. Use a plumb bob to check the perpendicularity, with an error of # 2mm. The distance between guide rails shall be parallel and equal, with error # 3mm. Fix the door shaft or door body on the cover plates at both ends. Then use a level ruler and a horizontal tube to check whether it is horizontal, with an error of # 2mm.

６、調整上下限位，門在運行中應流暢無異常響聲。所有啟動方式都應檢測試用。

6. Adjust the upper and lower limit, and the door shall be smooth without abnormal noise during operation. All starting methods shall be tested and tried.

７．將罩殼和扣板裝好，護帽和堵頭裝好后應將現場和門衛生清理。

7. Install the cover and gusset plate, and clean the site and door after installing the protective cap and plug.

８．按公司要求與客戶辦理有關結賬收款事宜。并及時將情況與有關部門匯投。

8. Handle settlement and collection matters with customers as required by the company. And timely report the situation to relevant departments.

此外要知道在國內卷簾門的尺寸并沒有統一的標準，卷簾門的大小及卷簾門門片的大小厚度都可以根據具體情況，按照客戶的要求及實際測量門洞的大小來確定卷簾門的尺寸。你有需求就來關注我們網站http://www.santoncc.cn并進行相應的聯系吧！

In addition, we should know that there is no uniform standard for the size of roller shutter doors in China. The size of roller shutter doors and the size and thickness of roller shutter door panels can be determined according to the specific situation, the customer's requirements and the actual measurement of the size of the door opening. Follow our website if you need http://www.santoncc.cn And make corresponding contact!