遙控卷簾門想必大家都不陌生，卷簾門可以分為無線好紅外線兩種，不管是哪種，用的時間長了任何東西都有壞的可能，那么濟南遙控卷簾門故障以及解決方法有哪些？

The remote control roller shutter door must be familiar to everyone. The roller shutter door can be divided into two types: wireless and infrared. No matter which one is used, anything can be broken after a long time. What are the faults and solutions of Jinan remote control roller shutter door?

1.電動機不動或轉速慢——毛病緣由普通是線路斷路、電機燒損、中止按鈕沒復位、限位開關舉措、負載較大等惹起。

1. The motor does not move or the speed is slow - the cause of the problem is generally caused by circuit breaking, motor burning, failure to reset the stop button, action of limit switch, large load, etc.

處置辦法：反省線路、并接通;改換燒損電機;改換按鈕或反復按動幾次;撥動限位開關滑塊使它脫離微動開關觸點，并調整微動開關地位;反省機器局部有無卡阻，若有則消弭卡阻清算妨礙物。

Solution: reflect on the line and connect it; Replace the burnt motor; Change the button or press it several times; Toggle the limit switch slider to separate it from the microswitch contact and adjust the position of the microswitch; Check whether the machine is blocked locally. If so, eliminate the blocking and clearing obstacles.

2.控制生效——毛病發作的部位及緣由：.繼電器(接觸器)觸點粘死、行程微動開關生效或觸片變形、滑塊緊定螺釘松、靠板螺絲松使靠板移位，使滑塊或螺母不能隨絲桿轉動而挪動、限位器傳動齒輪破損、按鈕上、下鍵卡死。

2. Control effectiveness - location and cause of disease onset: The contact of relay (contactor) is stuck, the travel micro switch is effective or the contact piece is deformed, the set screw of slider is loose, the screw of backup plate is loose, and the backup plate is displaced, so that the slider or nut cannot move with the rotation of the screw rod, the transmission gear of the limiter is damaged, and the upper and lower keys of the button are stuck.

處置辦法：改換繼電器(接觸器);改換微動開關或觸片;緊定滑塊螺釘并使靠板復位;改換限位器傳動齒輪;改換按鈕。

Disposal method: replace the relay (contactor); Replace the microswitch or contact piece; Tighten the slider screw and reset the backup plate; Replace the transmission gear of the stopper; Change button.

3.手拉鏈不動——毛病緣由：環形鏈條堵住十字槽;棘爪無脫離棘輪;壓鏈架卡死。

3. The hand zipper does not move - cause of the problem: the circular chain blocks the cross groove; The pawl does not disengage from the ratchet wheel; The pressure chain frame is jammed.

處置辦法：理順環形鏈條;調整棘爪與壓鏈架地位;改換或光滑銷軸。

Disposal method: straighten out the circular chain; Adjust the position of pawl and pressure chain frame; Replace or smooth the pin shaft.

4.電機振動或噪聲較大——毛病緣由：剎車盤不均衡或斷裂;剎車盤無緊固;軸承失油或生效;齒輪嚙合不順、失油或磨損嚴重;電機電流聲或振動.

4. Motor vibration or noise is large - cause of fault: brake disc is unbalanced or broken; The brake disc is not fastened; Bearing oil loss or effectiveness; Gear meshing is not smooth, oil loss or serious wear; Motor current sound or vibration

處置辦法：改換剎車盤或重新調整均衡;緊固剎車盤螺母;改換軸承;修配電機軸輸入端齒輪、光滑或改換;反省電機，如電機壞損則改換。

Solution: replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace the bearing; Repair the gear at the input end of the motor shaft, smooth or replace it; Check the motor and replace it if it is damaged.

5.反省電動卷閘門的支位偏向及螺絲松緊狀況，反省皮帶的松緊狀況，反省控制器對電機輸入清潔機箱外部的油污、灰塵反省自動電動門各部件的磨損狀況高速門，開關門寬度、速度、制動等狀況反省電壓參數能否正常維修、改換損壞的部件業主還需注重自動門的活期頤養與維護，自動門由于受裝置質量及運用環境的影響，運用進程中難免會發作成績。

5. Reflect on the support deviation of the electric rolling gate and the tightness of the screws, the tightness of the belt, the controller's input to the motor, the cleaning of the oil and dust outside the cabinet, the wear condition of the components of the automatic electric door, the width, speed, braking and other conditions of the high-speed door, the opening and closing width, the speed and the braking, and the voltage parameters. The owner also needs to pay attention to the current care and maintenance of the automatic door, Due to the influence of device quality and application environment, automatic doors will inevitably have problems in the process of application.

以上就是今天分享的遙控卷簾門的相關詳情，如果對您有幫助，就來關注我們網站http://www.santoncc.cn吧，為您提供更好更多的資訊！

The above is the relevant details of the remote control roller shutter door shared today. If it is helpful to you, please follow our website http://www.santoncc.cn Let's provide you with better and more information!