濟南卷簾門外形美觀，高強度，高韌性，耐腐蝕雙(單)層窗簾板，阻擋門外惡意入侵，更有效的保護，所以被廣泛應用，那么您知道它的安裝是怎樣的嗎？

Jinan roller shutter is widely used for its beautiful shape, high strength, high toughness, corrosion-resistant double (single) layer curtain plate, which can block malicious invasion outside the door and provide more effective safety protection. Do you know how it is installed?

1、檢查洞口和卷簾門的規格

1. Check the specifications of openings and rolling shutter doors

此項是正式安裝的準備工作。確定洞口位置，檢查洞口位置的準確性，確保洞口上方有足夠的空間容納卷簾門。其次，檢查卷簾門的型號是否正確，是否與孔的規格一致。

This is the preparation for formal installation. First, determine the position of the opening, check the accuracy of the opening position, and ensure that there is enough space above the opening to accommodate the roller shutter door. Secondly, check whether the model of the roller shutter door is correct and whether it is consistent with the specification of the hole.

2.安裝導軌

2. Install the guide rail

檢查導軌型號是否正確。然后，在孔處定位、劃線、鉆孔，然后固定導軌。兩個導軌的安裝方法相同，但要注意保證在同一水平線上。

First, check whether the guide rail model is correct. Then, position, scribe and drill the hole, and then fix the guide rail. The installation methods of the two guide rails are the same, but attention shall be paid to ensure that they are on the same horizontal line.

3.安裝左右支架

3. Install the left and right supports

檢查門洞的大小，并據此確定支架的具體安裝位置。然后，分別打孔固定左右支架。后，用水平儀調節兩個支架的水平度，確保它們水平。

Check the size of the door opening and determine the specific installation position of the support. Then, drill holes to fix the left and right brackets respectively. After that, adjust the levelness of the two supports with a level gauge to ensure that they are horizontal.

4.將車門車身安裝到支架上

4. Install the door body onto the bracket

根據門洞的位置確定軸的長度，然后將門體吊到支架上，用螺釘初步固定。然后，檢查門體與導軌和支架的連接是否良好。如果沒有問題，擰緊螺釘。如有問題，調試直問題解決。

First, determine the length of the central shaft according to the position of the door opening, then lift the door body onto the bracket and preliminarily fix it with screws. Then, check whether the door body is well connected with the guide rail and bracket. If there is no problem, tighten the screws. If there is any problem, debug until the problem is solved.

5.Spring調試

5. Spring debugging

順時針轉動彈簧。如果能扭轉一次，春天在黑暗中轉就正好了。彈簧調試完畢后，可以將門打開，引入導軌。

Turn the spring clockwise. If we can turn it around once, it will be just right for spring to turn in the dark. After the spring commissioning is completed, the door can be opened and introduced into the guide rail.

6.卷門開關的調試

6. Commissioning of rolling door switch

卷簾門安裝后，可打開和關閉幾次，以檢查其是否正常工作，螺釘是否擰緊。如果發現問題，可以及時解決，防止以后使用中發生事故。

After the roller shutter door is installed, it can be opened and closed several times to check whether it works normally and whether the screws are tightened. If problems are found, they can be solved in time to prevent safety accidents in future use.

7.安裝限位塊

7. Install the stop block

限位塊一般安裝在門體的底軌上，盡可能安裝在底軌上槽口的邊緣。

The limit block is generally installed on the bottom rail of the door body, and is installed on the edge of the notch on the bottom rail as far as possible.

8.安裝門鎖

8. Install the door lock

先確定門鎖的安裝位置，關閉門體，插入鑰匙，擰鑰匙使鎖管接觸門體軌道內側，然后做好標記，打開門體。然后，在標記的位置鉆孔，安裝門鎖，整個卷簾門安裝完畢。

First determine the installation position of the door lock, close the door body, insert the key, turn the key to make the lock tube contact the inner side of the door body track, and then make a mark to open the door body. Then, drill holes at the marked positions, install the door locks, and complete the installation of the whole rolling shutter door.

卷簾門有著可靠的平衡系統、強大的驅動裝置、制作精良的導軌和靈活的滾輪使車門運行輕便靈活，您在使用之前建議多多去了解相關信息，更多內容獲取就來我們網站http://www.santoncc.cn看看吧。

The rolling shutter door has a reliable balance system, a powerful driving device, a well-made guide rail and flexible rollers to make the door run light and flexible. You are advised to learn more about the relevant information before using it. For more information, please visit our website http://www.santoncc.cn Let's see.