卷簾門適用于各類商店和、賓館、銀行醫院、學校、機關、廠礦、車站、碼頭、倉庫、變電室及工業廠房等裝璜設施。卷簾門窗啟閉通常采用手動、電動兼手動或自動開啟方式，正常情況下門窗電動，遇臨時停電或其它情況則手動開閉。下面來講講卷簾門尺寸多少吧。

Roller shutter doors are suitable for all kinds of shops and shopping malls, hotels, banks, hospitals, schools, institutions, factories and mines, stations, wharves, warehouses, transformer rooms and industrial plants and other decoration facilities. The rolling shutter doors and windows are usually opened and closed manually, electrically and manually or automatically. Under normal circumstances, the doors and windows are electrically operated, and in case of temporary power failure or other circumstances, they are manually opened and closed. Now let's talk about the size of roller shutter door.

卷簾門尺寸：

Roller shutter door size:

1、防火卷簾門的安裝分為內裝和外裝，h:代表洞口高；w:代表洞口寬。內裝尺寸計算公式：w×（h+預卷＋封箱)×單價。外裝尺寸計算公式：w×（h+外跨尺寸+預卷＋封箱)×單價。說明：外跨尺寸：0.4m、預卷：0.6m。

1. The installation of fireproof rolling shutter door is divided into internal installation and external installation, h: represents the height of the opening; w: Represents the opening width. Calculation formula of interior dimension: W × (h+ pre roll + box sealing) × Unit Price. Calculation formula of external dimension: W × (h+ outer span size + pre winding + sealing box) × Unit Price. Note: outer span size: 0.4m, pre roll: 0.6m.

2、防火卷簾門封箱分為：三面和二面。三面封箱：高度要加1.6m，二面封箱：高度要加1.0m。例如：洞口尺寸為：3m*2m。內裝二面封箱面積為：3×（2＋0.6＋1.0）＝10.8平米。外裝二面封箱面積為：3×（2＋0.4＋0.6＋1.0）＝12平米。

2. The sealing box of fireproof rolling shutter door is divided into three sides and two sides. Three side sealing: the height should be increased by 1.6m, and two side sealing: the height should be increased by 1.0m. For example, the opening size is 3m*2m. The sealing area of two sides inside is: 3 × (2 + 0.6 + 1.0) = 10.8 square meters. The sealing area of the external two sides is: 3 × (2 + 0.4 + 0.6 + 1.0) = 12 square meters.

卷簾門安裝注意事項：

Precautions for installation of roller shutter door:

1、按設計型號，查閱產品說明書和電氣原理圖。檢查產品表面處理和零附件。量測產品各部位基本尺寸。檢查門洞口是否與卷簾門尺寸相符；導軌、支架的預埋件位置、數量是否正確。

1. Refer to the product manual and electrical schematic diagram according to the design model. Check the product surface treatment and accessories. Measure the basic size of each part of the product. Check whether the door opening is consistent with the size of the roller shutter door; Whether the position and quantity of embedded parts of guide rail and support are correct.

2、測量洞口標高，彈出兩導軌垂線及卷筒線。

2. Measure the elevation of the hole, and snap the vertical line of the two guide rails and the center line of the drum.

3、將墊板電焊在預埋鐵板上，用螺絲固定卷筒的左右支架，安裝卷筒。卷筒安裝后應轉動靈活。

3. Weld the backing plate on the embedded iron plate, fix the left and right supports of the drum with screws, and install the drum. The drum shall rotate flexibly after installation.

4、安裝減速器和傳動系統。

4. Install the reducer and drive system.

5、安裝電氣拴街系統。

5. Install electrical tie down system.

6、空載試車。

6. No load commissioning.

7、將事先裝配好的簾板安裝在卷筒上。

7. Install the curtain plate assembled in advance on the drum.

8、安裝導軌。按圖紙規定位置，將兩側及上方導軌焊牢于墻體預埋件上，并焊成以體，各導軌應在同一垂直平面上。

8. Install the guide rail. According to the position specified in the drawing, weld the guide rails on both sides and above to the embedded parts of the wall, and weld them into a body. Each guide rail should be on the same vertical plane.

9、安裝水幕噴淋系統，并與總控制系統連接。

9. Install the water curtain spray system and connect it with the main control system.

10、試車。先用手去試運行，再用電動機啟閉數次，調整無卡住、阻滯及異常噪音等現象為止。全部調試完畢，安裝防護罩。

10. Commissioning. Test run by hand first, and then open and close the motor several times until there is no jamming, blocking, abnormal noise and other phenomena. After all commissioning, install the protective cover.

11、安裝防護罩。濟南卷簾門卷筒上的護罩可做成方形，亦可做成半圓形。護罩的尺寸大小應與門的寬度和門條板卷起后的直徑相適應，保證卷筒將門條板卷滿后與護罩仍保持一定的距離，不得相互碰撞，經檢查無誤后，再與護罩預埋件焊牢。

11. Install the protective cover. The shield on the drum of Jinan roller shutter door can be made into a square or a semicircle. The size of the shield should be consistent with the width of the door and the diameter of the door slat after it is rolled up, so as to ensure that the drum still keeps a certain distance from the shield after the door slat is rolled up, and shall not collide with each other. After inspection, it can be firmly welded with the embedded parts of the shield.

卷簾門尺寸多少？以上就是問題的相關內容了，僅供參考，您可以根據自己的實際情況來考慮。更多事項就來網站咨詢http://www.santoncc.cn了解吧。

What is the size of the roller shutter door? The above is the relevant content of the problem, for reference only, you can consider it according to your actual situation. For more information, please come to the website for consultation http://www.santoncc.cn Understand.